language
EnglishEspañol
×

currentHome > Business > Revolutionary Materials > Nanofiltration Membrane > Carbonate Removal Nanofiltration Membrane

  • Carbonate Removal Nanofiltration Membrane
  • Carbonate Removal Nanofiltration Membrane

Carbonate Removal Nanofiltration Membrane

SL Lithium NF 8040 HS 40
SL Lithium NF 8040 HS 40 carbonate removal nanofiltration membrane are usually negative charged, which impedes the permeation of multivalent ions (e.g., carbonate ions) through electrostatic interactions. In addition, carbonate ions and the macro-molecular substances that formed by combing with them can be better retained, thus achieve the retention of carbonate. For monovalent ions like sodium ions, lithium ions, potassium ions, etc., the retention rate is rather lower, allowing them to pass through the membrane to a certain extent. Carbonate removal nanofiltration membrane has a wide range of applications in fields of water treatment, chemical industry, food, etc. It can be applied in improving water quality by removing carbonate ions, or in achieving the separation and purification of specific substance in certain manufacturing processes.
0086-000-0088 Download
Specifications
ModelMaterialArea / pcsApplication PressureGrid ThicknessDesalination Rate%
SL Lithium NF 8040 HS 40FRP260ft2/24m2600psi50mil96

Note:

1. Membrane flux and its desalination rate is based on following test conditions: 2000ppmMgSO4,70psi (4.8bar), 77℉ (25℃), 15% recovery rate.

2. The water yield of a single element may vary within a range of ±25%.

3. The stable desalination rate is normally achieved within 36 - 72 hours of continuous operation, depending on feeding features and operating conditions.

4. Sales specifications for this product may change slightly in accordance with design optimisation

5. Guaranteed active area ±5%.

Component size
Model

size(in./ cm.*)

ABC

Packing weight LBS/Kg
SL Lithium NF 8040 HS 4040.0/101.6   1.125/2.86    7.9/20.135/16

Note:

Membrane element fit into pressure vessels with engineered internal diameter of 8 in (20.3cm).  *1in=2.54cm

Run and wash parameterss
Operation flux range12~32LMH
Maximum operating pressure1600psi (41bar)
Maximum temperature tolerance2122°F (50°C)
Maximum tolerable pHContinuous operation2:3 – 10
CIP:2 – 11
Maximum pressure drop15psi (1.0bar)
Maximum chlorine tolerance3＜0.1 ppm
Influent water quality requirementsNTU < 1    SDI15 < 5

Note:

1. If the temperature is higher than 95°F (35°C), the maximum withstand pressure is 435psi (30bar).

2. The highest operating temperature is 95℉ (35℃) when pH value is lower than 10.5.

3. Under certain circumstances, free chlorine and other oxidising agents can cause premature failure of membranes, therefore, it is recommended to remove free chlorine before it contacts with membranes.

  • Preparations

    When the membrane system is ready to be commissioned, the membrane treatment system needs to be started up correctly to prevent damages to membrane elements caused by the overflow of feeding water and the hydraulic shock. The correct initiating sequence helps to ensure that the system’s operating parameters align with design requirements, so that the quality and quantity of produced water through the system reach designed objectives.

    Before the membrane system is initiated for the first time, pretreatment system debugging, elements loading, instrumentation debugging and calibration and ancillary equipment system debugging and so on shall be completed.

    Please contact us for more information.

    For more information, please contact us

  • Operation Guide

    During start-up, shutdown, cleaning, etc., to prevent potential damaged to membranes, any sudden changes of pressures or of crossflow flow in membrane elements shall be avoided. During start-up, it is suggested to follow the undermentioned procedures to gradually transit the system from shutdown to operating:

    Feeding pressure should be gradually escalated over a period of 30 ~ 90 seconds.

    The set peak of crossflow velocity should be gradually achieved over a period of 30~ 60 seconds.

    For more information, please contact us

  • Maintenance

    Once the membrane element is moisturized, it should always be kept moist.

    If users failed to strictly follow the set operating limitations, the warranty will be null.

    If the system need to be shut down for an extended period of time, it is recommended to immerse the membrane elements in protective solution to prevent microorganisms.

    The user shall be responsible for any damages to the membrane elements caused by using incompatible chemicals, lubricants, etc.

    The maximum pressure drop a single pressure vessel can tolerate is 50psi (3.4bar).

    Under all circumstances, backpressure must be avoided on the production side of the membrane system.

    For more information, please contact us

Label : Ceramic Membrane
Products
Related Products